Mercedes Oxygen Sensor POWER Performance CHIP
Mercedes Oxygen Sensor POWER Performance CHIP
You can gain +15-25 additional HP, and extreme acceleration gains of up to 20 % depending on stock engine performance.
Gain additional power without any consequence in relation to the driving comfort. The ECU runs as normal, but the signal of oxygen sensor power chip manipulates the signal every microsecond delivering higher horsepower, torque and acceleration as well. You can feel a refreshed engine, and dynamic acceleration without terrible flat pots.
FOR BEST RESULTS COMBINE WITH SURGE PERFORMANCE CHIP!
FEATURES OF O2 OXYGEN SENSOR POWERCHIP:
- Improves engine output by as much as 10 %.
- Enhance throttle response, acceleration and low end torque.
- Preserves smog certification.
- Pushes up acceleration and dynamism by upto 15 %.
- Results higher top speed.
- Lifetime Warranty
- Easy installation in 30 minutes.
- Switch can be connected in line for on/off
- Reduces flat spots or delay time when you mash down the throttle.
OPERATION OF OXYGEN SENSOR POWERCHIP
The device modifies voltage signals on your oxygen sensor. ECU lets more fuel to the injectors while air-fuel mixture is modified. This can influence the mixture adjustment gaining more power, enhancing the efficiency of combustion and saving fuel.
We improve the power slightly at the expense of emission.
HOW IS SUCH AN ENHANCED RESULT POSSIBLE?
The operation of injection / ignition system is significantly determined by the voltage of the oxygen sensor, therefore when the chip modifies this signal we may regulate effectively engine output.
Oxygen sensor powerchip unleashes lots power of your stock engine by turning off some engineering restrictions applied by the car manufacturer. This does not hurt your car or significantly effect emissions.
Features: |
|
|
Effect time: | immediate | |
Switch: | can be connected | |
Facture: | chromium body with melted epoxy | |
Model range: | full
|
|
Installation: | easy with twistlocks | |
Connection: | only to properly working OEM sensor | |
Warranty | 10 years | |
Smog certification: | preserved | |
INCLUDED: |
|
INSTALLATION OF O2 OXYGEN SENSOR POWERCHIP:
Before installation please be sure that stock sensor is working correctly because result might be diminished if stock oxygen sensor does not work with proper signals if your sensor is old or faulty.
COLORS:
Please make sure the red arrow on the oxygen chip points toward the engine.
1 wire version:
Use only the red wire (signal) in line. Cut one of the black wires and ground the other black one with the help of the clips to the exhaust piping or to the body.
2 wires version: Use the red in line (signal) and the black in line (ground) wires and cut the rest.
3 wires version: Use only the red wire (signal) in line. Cut one of the black wires and ground the other black one with the help of the clips to the exhaust piping or to the body.
4 wires version: Use only the red wire (signal) in line. Cut one of the black wires and ground the other black one with the help of the clips to the exhaust piping or to the body.
5 wires version: Use only the red wire (signal out !!! - not signal in) in line. Cut one of the black wires and ground the other black one with the help of the clips to the exhaust piping or to the body.
- Cut the wires about on halfway of the original cable cluster.
- Check colors and the operations of each wire in the O2 and the car user guide!
- Connect the suitable wires with twistlocks or weld it in place (muriatic acid helps to weld).
- Insulate the whole cable cluster with the heatproof insulating tube.
NOTE: WITH MODELS WHERE MORE THAN 1 PC. OXYGEN SENSOR IS WORKING, THE CHIP MUST BE CONNECTED TO THE REAR SENSOR (FROM REAR OF THE VEHICLE). PLEASE CHECK THE DRAW BELOW.
If there is two sensors fitted in each upstream or downstream bank (V6, V8) always 2 units are necessary as displayed in the description. Click here!
** For wiring colors visit: http://www.yourhotcar.com/O2.htm **